Centro de Documentos

Faça o download de datasheets, manuais de instalação, certificados e mais.

Filtrar por
Região
Sua seleção (11)
All Aplicativos e software
Todos documentos
(11)
Enphase Installer Portal release notes (24.1.0)
February 9, 2024

What’s new

For all installers:

1. Added ability to reverse the polarity of Storage CTs

Installers can now navigate to the Storage CT page under Devices and click Reverse Polarity to reverse the polarity of the respective Storage CT.

Screen to reverse Storage CT polarity

 

2. Added the ability to make a few reports available immediately under the Reports section

Previously, users had to wait 24 hours for enough data to be collected to prepare a report. In this release, we have added the ability to make the below reports available immediately without waiting 24 hours:

· IQ Relay Self-Test Report

· Grid Profile Settings Report

· Microinverter Routine Test Report

Ability to make a few reports available immediately under the ‘Reports’ section

For installers in the United States, Puerto Rico, and Canada:

The following products and their respective SKUs have been made eligible for labor reimbursement.

S. No. Product SKU
1 IQ Combiner 5 X-IQ-AM1-240-5
2 IQ Combiner 5C X-IQ-AM1-240-5C
3 IQ System Controller 3 SC200D111C240US01
4 IQ System Controller 3G SC200G111C240US01
5 IQ Battery 5 IQBATTERY-5P-1P-NA
6 IQ Combiner 4 X-IQ-AM1-240-4
7 IQ Combiner 4C X-IQ-AM1-240-4C
8 IQ Combiner 4 X2-IQ-AM1-240-4
9 IQ Combiner 4C X2-IQ-AM1-240-4C

What’s fixed

1. Fixed the issue of users not being able to select a device from search results in the Install Replacement section.

2. Fixed the issue of not showing System Controller Issue and Battery Issue system statuses in the System List.

3. Fixed the issue of showing non-relevant devices under the Devices tab of the system. Only those devices which are present in the system and reporting to the Enphase Cloud will be displayed to end users. The Devices tab will also consist of devices that had reported at least once for that particular system.

4. Relaxed the Array Builder validations so that both arrays can be built on the Array Builder for sites with both IQ8 Microinverters and other models of microinverters.

5. Updated Production CT health check logic to check for existing system status to provide recommendations.

Enphase App release notes (24.1.0)
February 9, 2024

What’s new

For all Enphase App users with microinverters:

  1. Notification when microinverters in your system do not report

    Whenever some of the microinverters in your system are not reporting, we will notify you via email, text message, or push message based on your notification preferences. This notification will be gradually rolled out to all users.

    To adjust your notification preferences, navigate to Menu > Account > My Notifications.

For Enphase App users in the U.S. and Canada with IQ EV Chargers:

  1. Additional details for IQ EV Charger on Live Vitals page 

    You can now see live Voltage and Current details for your IQ EV Charger, along with its live Power consumption, on the Live Vitals page.

    Details for IQ EV Charger on Live Vitals page

  2. Added IQ EV Charger energy consumption on the Energy page

    In the Day view on the Energy page graph, you can now see a breakdown of energy consumption between your IQ EV Charger and the rest of the household. This breakdown is shown in the pop-up when you hover on the graph.

    IQ EV Charger energy consumption on the Energy page

  3. Added IQ EV Charger energy consumption for custom periods

    You can now view details of your IQ EV Charger’s energy consumption for custom periods on the Energy page.

    IQ EV Charger energy consumption for custom periods

 

What’s fixed

  1. Fixed the issue of not displaying Last reported date for some devices.

  2. Fixed the issue of displaying erroneous battery charge and gateway connectivity events in Event History.

Enphase Installer App release notes (3.34.2)
January 8, 2024

What’s new

For installers in North America:

  1. New informational pop-up about IQ Battery 3T/10T wiring

    We have added guidelines for the recommended wiring procedure for an IQ Battery 3T/10T.

    These guidelines appear in a pop-up that also links to the latest IQ Battery 3T/10 quick install guide, as well as a short training video demonstrating best practices for IQ Battery 3T/10T wiring, if further instruction is needed.

    The pop-up will be shown whenever an IQ Battery 3T/10T is scanned.

    added a new informational popup about the wiring of IQ Battery 3T/10T

This release is being deployed via Google Play (Android) or App Store (iOS) upgrades.

Enphase Installer Portal release notes (23.9.0)
December 26, 2023

What’s new

For all installers:

  1. Added Service Manager link within the Installer Portal for easy access to a system

    Installers can now navigate to a system within the Service Manager from the Installer Portal as a logged-in user by clicking Service Manager within the system view.

    Service Manager Link within the Installer Portal

     

  2. Added ability to set Dark Mode and remove images within the kiosk view

    Installers can now set Dark Mode within the kiosk view as well as delete any uploaded images.

    ability to set Dark Mode and Remove Images within the Kiosk view 

    Option to enable/disable Dark Mode

     Option to remove the image and save 

    Option to remove an image and save

  3. Added a new SKU within the Microinverter Routine Test Report

    Installers in Thailand need to generate a routine test report for the MEA and submit it to the local utilities for interconnection agreements. In previous releases, we added the ability for installers—within the reports section for an individual site—to generate a report for the IQ7 Microinverters in a system. In this release, the IQ8P Microinverter below is added to the report.

    • IQ8P-72-2-INT

    Added a new SKU within the Microinverter Routine Test Report

     

What’s fixed

  1. Fixed the issue of Thai fonts not being downloaded correctly within the reports downloaded from the Installer Portal.

  2. Fixed the issue of legacy tariff editor not being available for ACB systems within the System Settings page.

  3. Fixed the issue of wrong device statuses showing up for Wireless Range Extender or device statuses not showing at all.

Enphase App release notes (23.9.0)
December 26, 2023

What’s new

For Enphase App users in the U.S. with Commercial Enphase Energy Systems:

  1. Commercial tariffs now available under Autofill section on Electricity Rate page

    You can now choose the relevant Tariff for your Commercial system from the Autofill list.

    To set your tariff structure, navigate to Menu > Settings > Electricity Rate > Autofill.

 

For Enphase App users in the U.S. and Canada with IQ EV Chargers:

  1. IQ EV Charger consumption data and session history added to Reports page

    You can now generate reports to access an IQ EV Charger’s consumption data and session history data.

    To generate these reports, navigate to Menu > System > Reports.

    IQ EV charger consumption data and Session History added in Report section

  2. Added details for Not Charging status of IQ EV Charger

    You can now see the reason why your IQ EV Charger is not charging.

    Details for non charging status of IQ EV Charger

  3. System status updated for users with standalone IQ EV Chargers

    Errors for IQ EV Chargers are displayed on the Status page, and more details about these errors can be viewed on the Notices page.

    To learn more about an error, tap on the error on the Status page.

    System Status updated for users with Standalone IQ EV chargers

What’s fixed

  1. Resolved display issues for battery charge and discharge data on the Energy and Status pages.

  2. Fixed issues with a system profile not being updated and stuck in a Pending state.

  3. Addressed issues with the Not Reporting Range Extenders display on the Devices page.

Enphase Installer App release notes (3.34.1)
December 14, 2023

What’s new

For all installers:  

  1. Added third-party storage device details in the System Details menu

    We have added an option for installers to add details of third-party storage devices if used along with Enphase components. 

    System-details

Note: Enphase recommends using Enphase IQ Batteries along with Enphase microinverters for the best user experience.

What’s fixed

For all installers:  

  1. We have fixed an issue that caused IQ Gateway updates to start and fail multiple times in some conditions.

  2. Improved app performance and other bug fixes.

This release is being deployed via Google Play (Android) or App Store (iOS) upgrades.

IQ Gateway software release notes (7.6.336)
December 8, 2023

IQ Gateway software version 7.6.336 supports IQ7 Series and M Series Microinverters along with IQ Battery 3T/10T and AC Battery for Germany, Belgium, Austria, France, Netherlands, and Switzerland.

  • Gateways supported: IQ Gateway Metered

  • Countries:  Austria, Belgium, France, Germany, Netherlands, Switzerland

  • Microinverters supported: IQ7 Series, M Series, third-party string inverters

  • Batteries supported: IQ Battery 3T/10T, AC Battery

  • Supported system configurations:

    • Grid-tied solar and storage systems with IQ7 Series Microinverters, IQ Gateway Metered, and IQ Battery 3T/10T

    • Grid-tied solar and storage systems with compatible third-party string inverters, IQ Gateway Metered, and IQ Battery 3T/10T

    • Grid-tied solar and storage systems with M Series Microinverters, IQ Gateway Metered, and IQ Battery 3T/10T

    • Grid-tied solar and storage systems with IQ7 Series Microinverters, IQ Gateway Metered, and AC Battery

    • Grid-tied solar and storage systems with M Series Microinverters, IQ Gateway Metered, and AC Battery

    #

    Feature

    Description

    1

    Bug fixes

    • Fixes the issue of multiple USB unplugged events observed in the Enphase Installer Portal.

    • Fixes the issue of microinverters, batteries, and other devices not reporting status by improving the Zigbee communication.

    • Fixes the issue of the Battery Management Unit (BMU) shutting down whenever the IQ battery is idle.

    • Fixes the issue of undesirable power consumption (tare loss) by the battery when in idle state.

    • Fixes the issue of IQ Battery maximum state-of-charge (SoC) being limited to 97% instead of 100%.

    • Fixes the issue of Phase Imbalance Management (PIM) getting enabled for single-phase systems.

     

    This release is being deployed via remote software upgrades for all systems.

Enphase Installer Portal release notes (23.8.0)
November 29, 2023

What’s new

For all installers:

  1. Informing installers in case of multiple polarity reversal attempts for the same system

    Installers will now be informed and asked for confirmation if they wish to proceed with the polarity reversal of any meter if the polarity of the same meter was reversed less than 24 hours before. This ensures that polarity reversal is not performed twice unintentionally, resulting in no change in polarity.

    Switch the polarity

     

  2. Added capability for installer company administrators to specify job roles at the time of new user creation

    At the time of new user creation, administrators of installer companies can now specify the job role that the new user has within the installer company. For example, this may include roles such as Project Manager, Marketing/Sales, and Finance.

    adding new user's image account details image

     

  3. Added ability to hide installer name at the time of kiosk creation using the Fleet dashboard

    We have implemented the ability to hide the installer company’s name and logo at the time of kiosk creation using the Fleet dashboard.

    Option to enable or disable the installer name and logo:

    new display profile image

     

    Example of the kiosk interface when the installer name and logo are disabled:

    new display profile image
  4. Allowed access to view kiosks created by other users within the same company

    Installer users will now be able to view kiosks created by other users belonging to the same company.

    access allowed to view kiosks

Bug fixes

  1. Fixed the loss of per-phase consumption and per-phase production curves with IQ Gateway replacement.

  2. Resolved language discrepancies for the reports section in French locale.

  3. Renamed the System Configurator in the Quick Access section to System builder.

  4. Added the Status Since column to the Fleet Status tab in the Fleet dashboard.

Enphase App release notes (23.8.0)
November 29, 2023

What’s new

For Enphase App users in the U.S. and Canada with IQ EV Chargers:

  1. Off-Peak times now displayed on Add-on Schedules page

    You can now view the off-peak charging schedule for charging your EV in the Off-Peak section of the Add-on Schedules page of the app.

    To set add-on schedules for EV charging, navigate to Menu > Settings > EV Charger > Add-on Schedules.

    Off- Peak Schedule displayed under Off-Peak Add-on Schedule

  2. IQ EV Charger details added to Live Vitals

    You can view live data for your IQ EV Charger, such as connection status and the amount of power consumed, on the Live Vitals page.

    To access the page, Navigate to Menu > System > Live Vitals.

    IQ EV charger details in Live Vitals

For systems in the U.K. with an IQ Battery 5P:

  1. Charge battery from the grid feature

    You can charge your batteries from the grid once the IQ Gateway software has been updated to version 8.2.82 or above.

    To access the Charge battery from the grid feature in the app, navigate to Menu > Settings > Battery.

What’s fixed

  1. Resolved issues with Live Status for multi-gateway systems.

  2. Addressed issues with generator on and off notifications.

  3. Updated the Available Power values displayed in the app for systems with an IQ Battery 5P in the U.K.

Enphase Installer App release notes (3.34.0)
November 22, 2023

What’s new

For all installers:

  1. Added best practices for Zigbee site layout (applicable for IQ Battery 3/3T, 10/10T)

    The app now provides recommendations for adding range extenders to an Enphase Energy System. Following these best practices can help reduce installation and troubleshooting times.

    Best practices for Zigbe site layout

  2. Added a reminder for breaker size details (applicable for IQ Battery 5P in North America)

    We have added a reminder to installers if breaker size details have not been added, and provided guidance on how to add the necessary details.

    reminder for breaker size details

For installers in Europe:

  1. Added voltage checks

    The Enphase Installer App will automatically check the voltage for all phases and show an error if the voltage is outside normal operating values (less than 20 V, or greater than 300 V) when using expert mode to enable the meters.

  2. Added battery configuration check

    The app will now restrict adding an AC Battery and an IQ Battery in the same system.

  3. Training requirement for commissioning

    The Enphase Installer App will block commissioning if the respective training is not completed for:

    • Grid-tied storage systems in the U.K.

    • Systems with an IQ Energy Router or IQ Energy Router+

What’s fixed

For all installers:

  1. Improved the performance of the Provisioning step in the app.

  2. Fixed an issue where installers were blocked for not completing the IQ Battery oversubscription step in systems with M Series Microinverters.

  3. Improved app performance and implemented other bug fixes.

IQ Gateway software release notes (7.3.621)
November 3, 2023

IQ Gateway software version 7.3.621 improves system stability.

  • Gateways supported: IQ Gateway, IQ Combiner 3/3C/3-ES/3C-ES/4/4C, IEEE 1547-2018 compliant IQ Gateway and IQ Combiner 4/4C, Envoy S Metered for North America, Envoy S Standard for North America, IQ Gateway Commercial, IQ Gateway M

  • Countries: U.S., Mexico, Canada, Brazil, Philippines

  • Microinverters supported: IQ8 Series, IQ7 Series, IQ6 Series, M Series, S Series

  • Supported system configurations:

  1. Grid-tied Solar Only systems with M Series or S Series Microinverters, Envoy S Metered for North America or Envoy S Standard for North America

  2. Grid-tied Solar Only systems with IQ6 Series Microinverters, IQ Gateway or IQ Combiner 3/3C/3-ES/3C-ES/4/4C

  3. Grid-tied Solar Only systems with IQ7 Series or IQ8 Series Microinverters, IQ Gateway or IQ Combiner 3/3C/3-ES/3C-ES/4/4C or IEEE 1547-2018 compliant IQ Gateway or IEEE 1547-2018 compliant IQ Combiner 4/4C

  4. Grid-tied Solar Only systems with IQ7AM Microinverters, IQ Gateway (residential) in Brazil and Mexico

  5. Grid-tied Solar Only systems with IQ7AM Microinverters, Envoy S Metered EM in Brazil and Philippines (230 V, 60 Hz systems only)

  6. Grid-tied Solar Only systems with IQ7 Series Microinverters, IQ Commercial Gateway in Brazil and Philippines (230 V, 60 Hz systems only)

  7. Grid-tied Solar Only systems with IQ7AM Microinverters, IQ Gateway Commercial in Brazil, Mexico, and Philippines (230 V, 60 Hz systems only)

  8. Sunlight Backup systems with IQ8 Series Microinverters, IQ Gateway or IQ Combiner 4/4C or IEEE 1547-2018 compliant IQ Gateway or IEEE 1547-2018 compliant IQ Combiner 4/4C, and IQ System Controller 2

  9. Home Essentials Backup or Full Energy Independence systems with IQ6 Series Microinverters, IQ Gateway or IQ Combiner 3/3C/3-ES/3C-ES/4/4C, IQ System Controller 1/2, and IQ Battery 3/3T/10/10T

  10. Home Essentials Backup or Full Energy Independence systems with IQ7 Series Microinverters, IQ Gateway or IQ Combiner 3/3C/3-ES/3C-ES/4/4C or IEEE 1547-2018 compliant IQ Gateway or IEEE 1547-2018 compliant IQ Combiner 4/4C, IQ System Controller 1/2, and IQ Battery 3/3T/10/10T

  11. Home Essentials Backup or Full Energy Independence systems with IQ8 Series Microinverters, IQ Gateway or IQ Combiner 4/4C or IEEE 1547-2018 compliant IQ Gateway or IEEE 1547-2018 compliant IQ Combiner 4/4C, IQ System Controller 2, and IQ Battery 3/3T/10/10T

  12. Home Essentials Backup or Full Energy Independence systems with M215 Series or M250 Series Microinverters, Envoy S Metered for North America, IQ System Controller 1/2, and IQ Battery 3/3T/10/10T

Note: The following features are supported only in specific configurations above:

Load Control, Generator Support, and solar circuit control (PV shedding) are supported in configurations 8 through 12.

Grid services are supported in configurations 9 through 12.

Release notes:

# Feature Description
1 Bug Fixes and Feature Enhancements
  1. Fixes an issue with the IQ Gateway due to memory corruption that results in boot failure.
  2. Fixes charge/discharge oscillation issues when:
    1. IQ Battery is at 100% State of Charge (SoC) with Constant Voltage (CV) mode active
    2. Incorrect reference voltage value is set followed by battery reset during CV mode.
  3. Fixes a Battery Management Unit (BMU) L1 error caused by toggling the DC switch of an IQ Battery.
  4. Fixes an issue to avoid BMU RMA due to wrong inventory report.
  5. Fixes the IQ Gateway database corruption observed during a software upgrade.
  6. Fixes an issue where automatic update of IQ Battery firmware failed due to a low SoC condition.

 

This release is being deployed via remote software upgrades for existing systems.